SSDieselSupply.com
SSDPro-Exhaust.com

Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Groups Groups
  • CAdiesel's Avatar
    01-08-2021, 02:29 PM
    CAdiesel replied to a thread Troubleshooting Lift Pump in Engine
    Ok, thanks Grant. I'll keep an eye on it.
    73 replies | 3923 view(s)
  • grancito's Avatar
    01-07-2021, 10:13 PM
    grancito replied to a thread Troubleshooting Lift Pump in Engine
    I'm just back from a 8 hour drive, some in the dark, and no gauge problem this time. I don't understand how the IP sees the cylinder imbalance....
    73 replies | 3923 view(s)
  • CAdiesel's Avatar
    01-07-2021, 06:35 PM
    CAdiesel replied to a thread Troubleshooting Lift Pump in Engine
    So this is what I know at this point... The volt gauge hasn't worked in the 11 or so years that I have owned the truck. In that time I have replaced...
    73 replies | 3923 view(s)
  • grancito's Avatar
    01-03-2021, 11:44 AM
    grancito replied to a thread Troubleshooting Lift Pump in Engine
    Let me know if you find the problem. I went on long drive yesterday, and 1 hour from home at night, the volt meter was reading very low, I guessed it...
    73 replies | 3923 view(s)
  • grancito's Avatar
    01-01-2021, 10:22 AM
    grancito replied to a thread Troubleshooting Lift Pump in Engine
    The gauge may have failed, the signal comes from the ignition switch circuit, so I am guessing that the gauge failed, because a break from there to...
    73 replies | 3923 view(s)
  • CAdiesel's Avatar
    12-29-2020, 11:37 AM
    CAdiesel replied to a thread Troubleshooting Lift Pump in Engine
    10-4 on the speed sensor. I’m taking the truck to a trans shop to get it the once over anyway but I’ll keep that in mind. Are you saying that the...
    73 replies | 3923 view(s)
  • grancito's Avatar
    12-28-2020, 09:04 AM
    grancito replied to a thread Troubleshooting Lift Pump in Engine
    Sounds like a connection problem on the speed sensor, check for that, and if you buy a new one, rockauto sells one with a new plug wired and heat...
    73 replies | 3923 view(s)
  • CAdiesel's Avatar
    12-27-2020, 11:10 PM
    CAdiesel replied to a thread Troubleshooting Lift Pump in Engine
    Speedo seemed to work ok but was a little bouncy. Sub sat for almost 4 years before I tore it apart this spring. It did run but I didn't want to push...
    73 replies | 3923 view(s)
  • grancito's Avatar
    12-27-2020, 08:59 PM
    grancito replied to a thread Troubleshooting Lift Pump in Engine
    The starting price for the sensor is $8 so no great cost if it isn't the problem. The speedometer should be using the same sensor, so it should have...
    73 replies | 3923 view(s)
  • CAdiesel's Avatar
    12-27-2020, 05:43 PM
    CAdiesel replied to a thread Troubleshooting Lift Pump in Engine
    Took Sub for a drive and it seems that the trans reset and I have all 4 gears... for now. Thanks for the reminder that although the SES light...
    73 replies | 3923 view(s)
  • grancito's Avatar
    12-26-2020, 05:06 PM
    grancito replied to a thread Troubleshooting Lift Pump in Engine
    Hell, you are not having much luck. My transmission in the 95 truck went into 1st gear only mode a few years ago, when I was 6 hours from home, and I...
    73 replies | 3923 view(s)
  • CAdiesel's Avatar
    12-26-2020, 02:04 PM
    CAdiesel replied to a thread Troubleshooting Lift Pump in Engine
    Finally got it running about 6 weeks ago, then left town for about a month. Here's what it took: I replaced the new lifters and had no change. So...
    73 replies | 3923 view(s)
  • grancito's Avatar
    11-28-2020, 04:14 PM
    Ok, good to fix it the right way.
    17 replies | 1256 view(s)
  • RipnRun's Avatar
    11-27-2020, 02:11 PM
    Good idea and thanks. I needed the truck and had already bought a new cable so I just went with that.
    17 replies | 1256 view(s)
  • grancito's Avatar
    10-26-2020, 07:27 PM
    I have an idea, I have been working on my house water pump, the pipe connections had the leaks sealed with wraps of tire inner tube, common repair...
    17 replies | 1256 view(s)
  • RipnRun's Avatar
    10-22-2020, 03:24 PM
    Thanks, I think the ball would have to be a lot bigger because my bushing is totally gone. I saw some youtube repair videos that used bushings bought...
    17 replies | 1256 view(s)
  • grancito's Avatar
    10-21-2020, 02:49 PM
    You could put some epoxy on the ball to make it bigger, after fitting the cable end, or force a piece of plastic hose over it. A new cable from...
    17 replies | 1256 view(s)
  • RipnRun's Avatar
    10-21-2020, 08:31 AM
    That helps, thank you for looking. On the transmission end of my cable there is only a hole and I wondered what was supposed to hold the cable to the...
    17 replies | 1256 view(s)
  • grancito's Avatar
    10-21-2020, 01:07 AM
    I had a look, and the plastic end must be clipped over a ball, it looks like the end unclips from the cable, but the end is not sold separate. I...
    17 replies | 1256 view(s)
  • grancito's Avatar
    10-19-2020, 02:33 AM
    Good news. I'll look at the connection on mine in a day or two, to see what can be done.
    17 replies | 1256 view(s)
  • RipnRun's Avatar
    10-18-2020, 07:15 PM
    Turns out when I crawled under the truck the cable wan't broken, it just slipped off the arm/pin at the transmission end. I slipped it on and the...
    17 replies | 1256 view(s)
No More Results