SSDieselSupply.com
SSDPro-Exhaust.com

Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Groups Groups
Filter by: Popular Clear All
  • putsk's Avatar
    05-16-2018, 03:43 PM
    Hello guys this is the first time I placed in the post, but I spent time on the forum quite a while. My brother and I need your help. One day last...
    10 replies | 251 view(s)
  • quvia1's Avatar
    05-31-2018, 07:29 PM
    quvia1 started a thread oil line replace in Main Forum
    April 2017. Fishon211 posted he installed the kit from Leroy diesel. Has anyone else had good luck with these and is the install as difficult as...
    6 replies | 122 view(s)
  • grvrjr's Avatar
    05-11-2018, 08:29 PM
    I am about to install new cylinder heads on my 95 c1500 6.5l. Never did it on a diesel before. Everyone keeps telling me to make sure I don't get any...
    3 replies | 137 view(s)
  • grancito's Avatar
    06-13-2018, 09:47 PM
    Sounds like timing is too advanced. Park on level ground, and use a level, if you can get it on the side of the IP with the manifold there. Level is...
    10 replies | 251 view(s)
  • putsk's Avatar
    06-13-2018, 02:18 PM
    Hi guys it seems that we have the no start issue finally figured out but we have one more that we just can't get over. When he did all the other...
    10 replies | 251 view(s)
  • grancito's Avatar
    06-13-2018, 10:50 AM
    grancito replied to a thread oil line replace in Main Forum
    Good to hear success. Also interesting to know that the later engine is OK to have the 3/8 cooler lines. I'm installing a new block with the high...
    6 replies | 122 view(s)
  • quvia1's Avatar
    06-12-2018, 12:08 PM
    quvia1 replied to a thread oil line replace in Main Forum
    Took the drive shaft off and it gave me just enough room. Nice system.No more leaks
    6 replies | 122 view(s)
  • quvia1's Avatar
    06-11-2018, 05:58 PM
    quvia1 replied to a thread oil line replace in Main Forum
    This is an update on the install. It went great until I went to put the fittings on the block. I got the wrong size for my year and Leroy sent me the...
    6 replies | 122 view(s)
  • quvia1's Avatar
    06-06-2018, 07:52 PM
    quvia1 replied to a thread oil line replace in Main Forum
    Thanks. I will warn the people. I will be changing hopefully friday and let everyone know. This forum used to be really active and I learned a lot...
    6 replies | 122 view(s)
  • grancito's Avatar
    06-05-2018, 08:07 PM
    grancito replied to a thread oil line replace in Main Forum
    The problem is, not many of the members are active. I looked at the oil lines in the suburban, and wondered if they should be replaced, it doesn't...
    6 replies | 122 view(s)
  • quvia1's Avatar
    06-05-2018, 07:28 PM
    quvia1 replied to a thread oil line replace in Main Forum
    Its bad when I have to reply to my own thread but I went ahead and ordered the kit. I will let people know how it went. I enjoy this forum but this...
    6 replies | 122 view(s)
  • putsk's Avatar
    05-20-2018, 10:53 PM
    Hi guys, You bet grancito, my brother was just having a alot of fun getting out.. *not*:) when he gets the part installed I'll let you know for sure...
    10 replies | 251 view(s)
  • grancito's Avatar
    05-20-2018, 05:37 PM
    Thanks for the success feed back. Ignition switches from 1995 on, fail a lot, mine did recently, but only gave intermittent electrical problems. Have...
    10 replies | 251 view(s)
  • putsk's Avatar
    05-20-2018, 12:45 PM
    Hey guys, thank you very much without your advice we would not have been able to figure it out it was ignition switch. Without your help we would...
    10 replies | 251 view(s)
  • grancito's Avatar
    05-18-2018, 04:41 PM
    Sorry for replying late, lot of business to complete yesterday. You see in my list of vehicles, 2 GMCs one year apart, and the fuse system is...
    10 replies | 251 view(s)
  • putsk's Avatar
    05-17-2018, 10:42 AM
    Hi, thanks for your reply could you tell me which fuse he needs to do this with there's like three different fuses or possibly more that it could be...
    10 replies | 251 view(s)
  • grancito's Avatar
    05-16-2018, 09:42 PM
    quvia1 could have something here, don't worry where the grounds are, jumper cable engine to body. Bypass the ignition switch with a jump wire from...
    10 replies | 251 view(s)
  • putsk's Avatar
    05-16-2018, 08:50 PM
    Hi, thanks for the reply. I never thought about the ignition switch either but I will let my brother know to check that. Not sure where all the...
    10 replies | 251 view(s)
  • quvia1's Avatar
    05-16-2018, 07:06 PM
    Need to fill in your profile. What year engine etc. Do you have fuel at injectors? Could be ign. switch. Also check your grounds.
    10 replies | 251 view(s)
  • grancito's Avatar
    05-14-2018, 02:50 PM
    The crossover pipe nuts were the stuck ones on mine and I had to set fire to things with the oxy/acetylene to get them loose, but if you replace one...
    3 replies | 137 view(s)
  • grvrjr's Avatar
    05-13-2018, 05:54 PM
    grvrjr replied to a thread Fuel line and injector caps in Engine
    I was thinking that with the masking tape. That was one of my options. Now the only thing I am worried about is breaking any of the manifold bolts....
    3 replies | 137 view(s)
  • grancito's Avatar
    05-12-2018, 12:33 PM
    Put the injector lines somewhere clean where dust is not blowing around. Wrap masking tape around the top of the injector so you have a protruding...
    3 replies | 137 view(s)
No More Results