hey guys,
I am getting dtc 14 intermittently. I fire up my truck in the am with scanner plugged in and the coolant temp reads 100 deg c then climbs to 125 deg c
and then drops to -2 deg c. It...
Type: Posts; User: 6536jim
hey guys,
I am getting dtc 14 intermittently. I fire up my truck in the am with scanner plugged in and the coolant temp reads 100 deg c then climbs to 125 deg c
and then drops to -2 deg c. It...
Hey guys,
After the last post, I broke down with the truck same issue, cut out
with no restart until I cycled key switch many many times. I decided to install
my snap-on scanner and...
Hey guys,
A little more information regarding my morning no start condition.
As I said before this only happens in the morning after the truck sits all night.
I forgot to mention...
Hey guys,
I will try to disconnect that plug next time the engine will not start.
Should the engine after cranking and cranking without glow plugs working, in
normal outside temps...
Hey Guys,
I am having an issue now with my truck not starting in the am
after sitting all night. It does not happen every day. I will go out turn the key
the glow plug light goes...
Hey Grancito,
Can I check the ground cables with an ohm meter
to determine resistance level? If so what value should I look for?
I always remove, clean and retighten...
Hey guys,
I just replaced my starter once again after 3 or 4 years
with an a/c delco reman unit assembled in mexico. Before removing and
replacing I was getting the clicking sound...
Hey Grancito,
Both the trans output shaft splines and the input splines on the
transfer case are wiped. I can take the output shaft of the trans and literally
spin that in the...
Hey guys,
My input carrier assembly (input shaft + planetary) needs replacement. Splines are gone. Does anyone have one? I have tried to
locate one. So far no go, discontinued. ...
Hey guys,
I finally tore down my truck. The transmission output shaft is finished.
The splines are all wore out. Finding parts for the nv 4500 is no problem, however finding an input...
Hey guys,
I was driving today when i heard a loud bang from the trans. The truck came
To a stop and that was all she wrote. The clutch pedal feels normal and i am able
To shift thru the geas...
Grancito,
I dont remember seeing the tps light coming on. It may
of come on for a second or two and then off. I ran the truck today
with my scan tool hooked up and just got 35, 36...
Grancito,
I bought a reman from a/c delco double checked
number on the ecm should be correct.
Hi Guys,
I am getting several codes and was wondering if you might be able to point me in the right direction. Codes 35,36,57,62,84. Codes 35 and 36
I am not so concerned with I think...
Hey guys,
My 94 is throwing code 36. I have begun adding 2 cycle oil
and trans fluid in the hopes that will correct the problem. pump was replaced
about 35-40k miles ago. Is there...
Hey guys,
I think I finally solved this problem. The rig broke down today very
close from home. The motor cut out like it was not getting any fuel. After
bleeding the filter several times I...
Ok Guys,
I tried running down the road without the gas cap and I got the same
readings. The lift pump is brand new (which doesnt mean anything). You
guys gave me a thought, what I will do next...
hey guys,
ok today I replaced all the supply fuel line from the fuel tank sending unit
to the fuel filter. Now everything is new from the fuel tank to the fuel filter.
while i replaced lines i...
Hey guys,
Yes the bleeder on top of the filter. i would open
the black knock and hear a little hiss, then hot wire the pump and it would take several seconds before feul would flow...
Hey Guys,
I am still working on my rig. i went ahead and replaced the lift pump and
oil pressure switch for good measure. My truck ran really good for one or
two days and now it is still...
Hey guys,
I spent a lot of time this weekend trouble shooting my rig.
I checked the fuel pressure from the lift pump and got almost 9 lbs.
volume checked out good 1/2 pint or more in...
Hey guys,
i recently changed my turbo boost solenoid and once
my turbo was working properly my rig began to buck and hesitate badly
under high acceleration. Sounded like a fuel...
Hey Guys,
I recently replaced my waste gate solenoid after getting the
code 78. I have 15 psi at the waste gate valve at idle now. When i run the
truck and accelerate heavy the...
Hi, I got the center section of my turbo from Pensacola fuel injection for
about 375.00 w/exchange. 800.622.5103. my rig is a 1994
Hey guys,
Should the vacum pump pulley rotate smooth and with little or no resistance?
My truck was making a funny metal on metal or bad bearing noise and the belt was giving off some odor. I...