SSDieselSupply.com
SSDPro-Exhaust.com

Search:

Type: Posts; User: grancito

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    15
    Views
    686

    I have an idea, I have been working on my house...

    I have an idea, I have been working on my house water pump, the pipe connections had the leaks sealed with wraps of tire inner tube, common repair by the water company. It lasts a long time, you...
  2. Replies
    15
    Views
    686

    You could put some epoxy on the ball to make it...

    You could put some epoxy on the ball to make it bigger, after fitting the cable end, or force a piece of plastic hose over it. A new cable from rockauto is $55.
  3. Replies
    15
    Views
    686

    I had a look, and the plastic end must be clipped...

    I had a look, and the plastic end must be clipped over a ball, it looks like the end unclips from the cable, but the end is not sold separate. I looked for an easy way to remove the end to examine it...
  4. Replies
    15
    Views
    686

    Good news. I'll look at the connection on mine in...

    Good news. I'll look at the connection on mine in a day or two, to see what can be done.
  5. Replies
    15
    Views
    686

    Cheap, I guess. It is a pain to change from the...

    Cheap, I guess. It is a pain to change from the old chev or the 1994 to the 1995, I drive for miles in 3rd gear, because the shift distance on the gear shift is really short. I hope the new new...
  6. Replies
    15
    Views
    686

    You should have researched HOAs, many sad or...

    You should have researched HOAs, many sad or horror stories. I hope it is worth the suffering to please your wife.
  7. Replies
    15
    Views
    686

    My 1995 has a cable, but not the 1994. You can...

    My 1995 has a cable, but not the 1994. You can feel the cable through the carpet, it runs under the driver's feet and makes a loop under the drivers seat then goes forward and through the side of the...
  8. Replies
    61
    Views
    3,004

    I always have a problem with this site to send...

    I always have a problem with this site to send photos, and they are usually rejected for size. This time I can't access my camera or computer files, only photos I once posted. PM your email to me and...
  9. Replies
    61
    Views
    3,004

    After priming, I didn't try to compress them, but...

    After priming, I didn't try to compress them, but did compress a used one, that had oil in it, to take it apart. Any indication of the reason they were stuck, when you took them apart? Without...
  10. Replies
    61
    Views
    3,004

    How long did it take to get pressure? The filter...

    How long did it take to get pressure? The filter problem I had, caused oil pressure delay, the same as after an oil change, about 10 seconds, which would be equal to 30 seconds cranking. I don't...
  11. Replies
    61
    Views
    3,004

    OK good, one more possibility eliminated. The...

    OK good, one more possibility eliminated. The only other test I can think of, is to push the "closed valve"open, it is possible by hand, and have someone put something between the rocker and push...
  12. Replies
    61
    Views
    3,004

    The standard used ones I have are 0.922 inches

    The standard used ones I have are 0.922 inches
  13. Replies
    61
    Views
    3,004

    Did you keep an old lifter? A wild guess from me...

    Did you keep an old lifter? A wild guess from me is that you could have 10 thou oversize original lifters, and new loose ones are letting the oil in all of the time and over inflating them. Do you...
  14. Replies
    61
    Views
    3,004

    Good, Walt was helpful with my engine, I hope he...

    Good, Walt was helpful with my engine, I hope he comes up with a solution, I'll wait for results.
  15. Replies
    61
    Views
    3,004

    Send SSD an email, they are helpful, the parts...

    Send SSD an email, they are helpful, the parts are theirs, and they may have seen the problem before.
  16. Replies
    61
    Views
    3,004

    There is so much "use silicone instead of...

    There is so much "use silicone instead of gaskets" these days, I had to ask. The mineral spirits question ......? What is it other than a non viscous liquid, well low viscosity. I don't think that...
  17. Replies
    61
    Views
    3,004

    I bought the lifters rods and rockers from rock...

    I bought the lifters rods and rockers from rock auto because SSD didn't stock all of the parts, they worked fine, then bought 2 heads from SSD and used one for a few minutes, it worked fine. I am...
  18. Replies
    61
    Views
    3,004

    It is now more confusing because both heads have...

    It is now more confusing because both heads have a compression problem. You need to measure a push rod length, and compare with an old one. Where did the parts come from?
  19. Replies
    61
    Views
    3,004

    When the lifter is in the back of the cam...

    When the lifter is in the back of the cam position, any force from the push rod, will overcome the weak spring in the lifter, and push the tiny piston down, releasing the oil back into the gallery....
  20. Replies
    61
    Views
    3,004

    I don't have the spec for the valves, only read...

    I don't have the spec for the valves, only read it and didn't save it because I had new heads and block. The valve grind should not be a problem, as no machine cutting was used. If you find...
  21. Replies
    61
    Views
    3,004

    Yes you need the starter for a compression test....

    Yes you need the starter for a compression test. Hopefully you didn't lap the valves in a lot, the lifter tolerance is limited, but I can't remember where the measurement of protruding valve stem is...
  22. Replies
    61
    Views
    3,004

    It spins clockwise, the air out the intake sounds...

    It spins clockwise, the air out the intake sounds bad. There is an exhaust port on the intake side of each head, for S vin engines to recirculate exhaust gas. Did you replace the heads or just some...
  23. Replies
    61
    Views
    3,004

    You should be able to turn some of the push rods....

    You should be able to turn some of the push rods. Check if any push rods have up and down movement, push down on the rod end of the rocker to check for a spongy feeling. I ran mine with the covers...
  24. Replies
    61
    Views
    3,004

    From memory, a bad crank sensor will give a no...

    From memory, a bad crank sensor will give a no start, but the engine will start without it connected. When you said the engine turns over "not so rough" with the ECM fuse out, you are describing...
  25. Replies
    61
    Views
    3,004

    I have not heard of head differences causing a...

    I have not heard of head differences causing a problem. Big job to remove the rocker covers, but I can't think of why it won't start. I have run mine with the rocker covers off, it makes a mess from...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4