SSDieselSupply.com
SSDPro-Exhaust.com

Search:

Type: Posts; User: grancito

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    73
    Views
    3,930

    I'm just back from a 8 hour drive, some in the...

    I'm just back from a 8 hour drive, some in the dark, and no gauge problem this time. I don't understand how the IP sees the cylinder imbalance. Ignore codes if nothing is malfunctioning. Your VSS...
  2. Replies
    73
    Views
    3,930

    Let me know if you find the problem. I went on...

    Let me know if you find the problem. I went on long drive yesterday, and 1 hour from home at night, the volt meter was reading very low, I guessed it was the alternator regulator failure, the...
  3. Replies
    73
    Views
    3,930

    The gauge may have failed, the signal comes from...

    The gauge may have failed, the signal comes from the ignition switch circuit, so I am guessing that the gauge failed, because a break from there to instrument cluster is unlikely.
  4. Replies
    73
    Views
    3,930

    Sounds like a connection problem on the speed...

    Sounds like a connection problem on the speed sensor, check for that, and if you buy a new one, rockauto sells one with a new plug wired and heat shrink included, kind of tells a story that the...
  5. Replies
    73
    Views
    3,930

    The starting price for the sensor is $8 so no...

    The starting price for the sensor is $8 so no great cost if it isn't the problem. The speedometer should be using the same sensor, so it should have been unstable. Check the plug and sensor pins for...
  6. Replies
    73
    Views
    3,930

    Hell, you are not having much luck. My...

    Hell, you are not having much luck. My transmission in the 95 truck went into 1st gear only mode a few years ago, when I was 6 hours from home, and I had a flight to the other side of the world. So I...
  7. Replies
    17
    Views
    1,266

    Ok, good to fix it the right way.

    Ok, good to fix it the right way.
  8. Replies
    17
    Views
    1,266

    I have an idea, I have been working on my house...

    I have an idea, I have been working on my house water pump, the pipe connections had the leaks sealed with wraps of tire inner tube, common repair by the water company. It lasts a long time, you...
  9. Replies
    17
    Views
    1,266

    You could put some epoxy on the ball to make it...

    You could put some epoxy on the ball to make it bigger, after fitting the cable end, or force a piece of plastic hose over it. A new cable from rockauto is $55.
  10. Replies
    17
    Views
    1,266

    I had a look, and the plastic end must be clipped...

    I had a look, and the plastic end must be clipped over a ball, it looks like the end unclips from the cable, but the end is not sold separate. I looked for an easy way to remove the end to examine it...
  11. Replies
    17
    Views
    1,266

    Good news. I'll look at the connection on mine in...

    Good news. I'll look at the connection on mine in a day or two, to see what can be done.
  12. Replies
    17
    Views
    1,266

    Cheap, I guess. It is a pain to change from the...

    Cheap, I guess. It is a pain to change from the old chev or the 1994 to the 1995, I drive for miles in 3rd gear, because the shift distance on the gear shift is really short. I hope the new new...
  13. Replies
    17
    Views
    1,266

    You should have researched HOAs, many sad or...

    You should have researched HOAs, many sad or horror stories. I hope it is worth the suffering to please your wife.
  14. Replies
    17
    Views
    1,266

    My 1995 has a cable, but not the 1994. You can...

    My 1995 has a cable, but not the 1994. You can feel the cable through the carpet, it runs under the driver's feet and makes a loop under the drivers seat then goes forward and through the side of the...
  15. Replies
    73
    Views
    3,930

    I always have a problem with this site to send...

    I always have a problem with this site to send photos, and they are usually rejected for size. This time I can't access my camera or computer files, only photos I once posted. PM your email to me and...
  16. Replies
    73
    Views
    3,930

    After priming, I didn't try to compress them, but...

    After priming, I didn't try to compress them, but did compress a used one, that had oil in it, to take it apart. Any indication of the reason they were stuck, when you took them apart? Without...
  17. Replies
    73
    Views
    3,930

    How long did it take to get pressure? The filter...

    How long did it take to get pressure? The filter problem I had, caused oil pressure delay, the same as after an oil change, about 10 seconds, which would be equal to 30 seconds cranking. I don't...
  18. Replies
    73
    Views
    3,930

    OK good, one more possibility eliminated. The...

    OK good, one more possibility eliminated. The only other test I can think of, is to push the "closed valve"open, it is possible by hand, and have someone put something between the rocker and push...
  19. Replies
    73
    Views
    3,930

    The standard used ones I have are 0.922 inches

    The standard used ones I have are 0.922 inches
  20. Replies
    73
    Views
    3,930

    Did you keep an old lifter? A wild guess from me...

    Did you keep an old lifter? A wild guess from me is that you could have 10 thou oversize original lifters, and new loose ones are letting the oil in all of the time and over inflating them. Do you...
  21. Replies
    73
    Views
    3,930

    Good, Walt was helpful with my engine, I hope he...

    Good, Walt was helpful with my engine, I hope he comes up with a solution, I'll wait for results.
  22. Replies
    73
    Views
    3,930

    Send SSD an email, they are helpful, the parts...

    Send SSD an email, they are helpful, the parts are theirs, and they may have seen the problem before.
  23. Replies
    73
    Views
    3,930

    There is so much "use silicone instead of...

    There is so much "use silicone instead of gaskets" these days, I had to ask. The mineral spirits question ......? What is it other than a non viscous liquid, well low viscosity. I don't think that...
  24. Replies
    73
    Views
    3,930

    I bought the lifters rods and rockers from rock...

    I bought the lifters rods and rockers from rock auto because SSD didn't stock all of the parts, they worked fine, then bought 2 heads from SSD and used one for a few minutes, it worked fine. I am...
  25. Replies
    73
    Views
    3,930

    It is now more confusing because both heads have...

    It is now more confusing because both heads have a compression problem. You need to measure a push rod length, and compare with an old one. Where did the parts come from?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4