SSDieselSupply.com
SSDPro-Exhaust.com

Search:

Type: Posts; User: Tombrewster421

Search: Search took 0.00 seconds.

  1. I have a 99 suburban and I was wondering if...

    I have a 99 suburban and I was wondering if anyone knew if a truck tank or newer suburban tank would fit next to the frame rail in order to achieve a dual tank setup? Also what would be the best way...
  2. Replies
    24
    Views
    6,164

    You say you relocated the PMD. Is it mounted on a...

    You say you relocated the PMD. Is it mounted on a heat sync and grounded well?
  3. Replies
    28
    Views
    9,745

    So on one of my suburbans I recently replaced the...

    So on one of my suburbans I recently replaced the starter. After doing so it still didn't want to start. I tightened the battery cables more and it started. I noticed that when it didn't start that...
  4. Replies
    12
    Views
    4,210

    Thi is exactly what mines been doing and it...

    Thi is exactly what mines been doing and it pisses me off since I got the FSD From ssdiesel two years ago. Now I need to figure out where to get a long enough extension harness to move it to the...
  5. Replies
    20
    Views
    6,559

    I want to do this also. Please keep us updated.

    I want to do this also. Please keep us updated.
  6. Replies
    2
    Views
    1,357

    My suburban has almost no power steering at idle...

    My suburban has almost no power steering at idle but is ok when revved up a bit. I think it's probably that valve like you say. I haven't replaced anything yet but I know the auto part stores have...
  7. Replies
    1
    Views
    2,291

    The transfer case that normally goes with the...

    The transfer case that normally goes with the 4l80 has the front driveshaft on the drivers side. I'm not sure if other transfer cases will bolt up to it or not but I would think you'd be able to find...
  8. Replies
    29
    Views
    11,379

    What would be a good idea? I basically want to...

    What would be a good idea? I basically want to know of its normal for it to defuel when the knob is turned one way. If I turn it right it's like I'm just turning down the fuel directly and the truck...
  9. Replies
    29
    Views
    11,379

    So I put the pot in using your schematic. At...

    So I put the pot in using your schematic. At first I had the knob turned all the way right and it made the engine defuel. I turned it half way and it was still defueling but not as much. Turned the...
  10. Replies
    7
    Views
    2,398

    On the other hand I have seen shop heaters that...

    On the other hand I have seen shop heaters that burn used motor oil. Wish I had one.
  11. Replies
    2
    Views
    917

    Well I just sold my 97 k2500 silverado 5.7 liter...

    Well I just sold my 97 k2500 silverado 5.7 liter for $3200. It was loaded with power options and had 220,000 on it. It is the gas motor though. Standard cab long bed.
  12. Replies
    29
    Views
    11,379

    I already did the mechanical waste gate on mine...

    I already did the mechanical waste gate on mine and it has defueled a couple times on long hills. How do you know where to set the pot in order to stop it?
  13. After disconnecting the valve on the power...

    After disconnecting the valve on the power steering pump it is still hard to steer. Does anyone know how to check the valve or if the pump is worn?
  14. After a bit of googleing I found out that the...

    After a bit of googleing I found out that the problem may be the EVO sensor on the steering shaft. I'll unplug it to find out if that is the problem and post back later.
  15. Power steering electronic variable orifice

    Does anyone have any idea on how to test if the electronic variable orifice is what's wrong with a power steering pump? It's very difficult to steer at idle in the parking lot but gets a little...
  16. Replies
    12
    Views
    5,190

    So I pulled out the HVAC controls in the dash and...

    So I pulled out the HVAC controls in the dash and found that one of the printed wires on the ribbon cable was burnt up. I guess I found my problem.
  17. Thread: lites

    by Tombrewster421
    Replies
    3
    Views
    3,083

    I actually found the easiest way to replace the...

    I actually found the easiest way to replace the pins on your own is to take off the front fender. You can leave the door shut and disconnect the wires then drive out the pins. Then you can open the...
  18. Replies
    5
    Views
    3,882

    Yup that was the problem. Thanks for the heads up.

    Yup that was the problem. Thanks for the heads up.
  19. Replies
    4
    Views
    2,544

    The tach would also be wrong I think.

    The tach would also be wrong I think.
  20. Replies
    12
    Views
    5,190

    I've got a similar issue also. In my 97 while I...

    I've got a similar issue also. In my 97 while I was driving the vent switched to defrost only and went full cold. The heat and vent selectors just won't do anything anymore. The fan switch works fine...
  21. Replies
    2
    Views
    1,133

    Thank you.

    Thank you.
  22. Replies
    2
    Views
    1,133

    Boost pressure?

    So with some helpful info I found on here I figured out how to ditch the factory vacuum controlled waste gate actuator in favor of a home made mechanical one. The vacuum lines had holes in them from...
  23. Replies
    5
    Views
    1,987

    Could also be as simple as the dimmer for the...

    Could also be as simple as the dimmer for the dash lights, if it's pushed up to all the way bright then a little more it will click to the position that turns on the dome light.
Results 1 to 23 of 23