SSDieselSupply.com
SSDPro-Exhaust.com

Search:

Type: Posts; User: quvia1

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    119

    Took the drive shaft off and it gave me just...

    Took the drive shaft off and it gave me just enough room. Nice system.No more leaks
  2. Replies
    6
    Views
    119

    This is an update on the install. It went great...

    This is an update on the install. It went great until I went to put the fittings on the block. I got the wrong size for my year and Leroy sent me the right size. Turns out I have a 97 and being a...
  3. Replies
    6
    Views
    119

    Thanks. I will warn the people. I will be...

    Thanks. I will warn the people. I will be changing hopefully friday and let everyone know. This forum used to be really active and I learned a lot from everyones threads. Hope it picks up again. This...
  4. Replies
    6
    Views
    119

    Its bad when I have to reply to my own thread but...

    Its bad when I have to reply to my own thread but I went ahead and ordered the kit. I will let people know how it went. I enjoy this forum but this is the second post I wrote without a reply. :(
  5. Replies
    6
    Views
    119

    oil line replace

    April 2017. Fishon211 posted he installed the kit from Leroy diesel. Has anyone else had good luck with these and is the install as difficult as Fishon211 states. Mine looks easy to get at the old...
  6. Replies
    10
    Views
    247

    Need to fill in your profile. What year engine...

    Need to fill in your profile. What year engine etc. Do you have fuel at injectors? Could be ign. switch. Also check your grounds.
  7. I agree. Load it up with additive.Possibly put it...

    I agree. Load it up with additive.Possibly put it right in fuel filter housing. Will hopefully clean the one or more injectors that are sticking.You'll kn ow when it is clean and not sticking.
  8. Replies
    19
    Views
    1,838

    Thanks. I will keep mine stock and stay away from...

    Thanks. I will keep mine stock and stay away from the turbo master. I will hook up a boost gauge in spring and go from there.
  9. Replies
    19
    Views
    1,838

    I am a little confused with this setup. Did you...

    I am a little confused with this setup. Did you go back to your vacumme waste gate operation or are you using your mechanical home made turbo master. I am hoping to increase my boost with a turbo...
  10. Replies
    2
    Views
    1,157

    my extension cable went last year. If I wiggled...

    my extension cable went last year. If I wiggled it near the connection the truck would start. One of the connectors pulled out of the plug. It took a while to find it. Replaced the cable and all i s...
  11. Replies
    1
    Views
    674

    OK. After a lot of checking around I found a...

    OK. After a lot of checking around I found a scamatic on the system and found out the back tank fills the front when the front tank is 25% lower than the back tank. Then the balance control module...
  12. Replies
    1
    Views
    674

    Fuel delivery problem

    I own a 97 ambulance which I converted into a camper. Drove it camping last week and after filling I put 14 gallons in the rear tank and 1 gallon in the front tank. Seemed wierd to me and after...
  13. Replies
    0
    Views
    1,076

    glow plug harness

    Has anyone made a harness just using new wire without thefuseable links? I saw a post where someone used a fuse on each wire.. The harness is so expensive so is this why? Can I just splice in new...
  14. Replies
    2
    Views
    528

    Wix are good and I use Napa gold with good...

    Wix are good and I use Napa gold with good results. They may even be a wix brand
  15. Thread: oil lines

    by quvia1
    Replies
    4
    Views
    902

    I have a few GM's diesel and not. I have found...

    I have a few GM's diesel and not. I have found out you are going to pay more but using GM part for the oil lines is the only way to go. I just had an aftermarket line blow off and lost all oil in...
  16. Replies
    2
    Views
    659

    Since I asked this question I found out the only...

    Since I asked this question I found out the only way to replace the element was to replace the seat because they are sewn in to the leather seat. I can put in an after market one if needed. Youtube...
  17. Replies
    2
    Views
    659

    Heated seats on suburban

    I have a few 99 suburbans and love them. One big problem are the heated seats on the drivers side with leather. they seem to burn out elements and they aren't cheap if you can find them at all. What...
  18. Replies
    0
    Views
    1,143

    Neutral safty switch

    Just a little advice when you change the switch on a 97 3500. What a stupid idea someone had at the factory to glue the two plugs in the unit. There are ways to get it apart but why in the first...
  19. Thread: wrong heads

    by quvia1
    Replies
    3
    Views
    1,350

    Why would you want to try to make it work. They...

    Why would you want to try to make it work. They ordered the wrong heads and should replace them.,Simple as that.
  20. Replies
    3
    Views
    1,370

    Thanks. I didn't think it would be that easy.

    Thanks. I didn't think it would be that easy.
  21. Replies
    3
    Views
    1,370

    Oil cooler lines on 99 burb

    Any one know if the oil cooler lines can be bypassed on this 99 Burb. Tired of changing these lines and the truck has never towed anything. This is also a gas truck but dont think it would be any...
  22. Replies
    66
    Views
    12,847

    Positive to the terminal end,neg to the threads....

    Positive to the terminal end,neg to the threads. Just a second or two will let you know. Dont hold on to the probe end when doing this.
  23. Replies
    66
    Views
    12,847

    I have the tool (socket) and used it once but...

    I have the tool (socket) and used it once but usefull. Relay controller can always be used as a spare but you shouldn't need it.
  24. Replies
    66
    Views
    12,847

    The starter is easy to take out and a pia to put...

    The starter is easy to take out and a pia to put back. There is a mounting bracket on front toward bumper and make sure you attach when installing. It keeps the torque from breaking the mounting...
  25. Replies
    6
    Views
    1,876

    If the pump is running when engine in running it...

    If the pump is running when engine in running it could be the fuel pickup in tank is clogged.
Results 1 to 25 of 109
Page 1 of 5 1 2 3 4